Skip to main content

Departures (Leaving the CTR)

First Contact (Ground)

On first contact with a VFR departure, Ground should assign them a squawk code, provide the local QNH (together with startup clearance, if the aircraft requires it), and ask for their intentions.

Ground should coordinate any VFR flight with TWR before the aircraft reaches the runway holding point, to notify TWR of the aircraft’s intentions. This is so that TWR may advise if they can accept the VFR aircraft’s intended operations in the CTR.

Some pertinent points to remember include:

  • Single-engine aircraft, which often fly VFR, do not require startup clearance. Twin/multi-engine aircraft and helicopters require startup clearance.
  • Light aircraft, which make up the majority of VFR traffic, sometimes request to perform an engine run-up. Run-up locations are noted in the aerodrome charts, or in airport LOPs. For example:
    • At BIKF, there is a run-up pad abeam of taxiway K.
    •  At BIRK, there are two run-up areas – south of Hangar 4 (on the North Apron, next to taxiway G), and one southwest of Hangar 8 (on the East Apron).

As with IFR, VFR aircraft must have their squawk code set & transponder on (XPDR/Mode C) before taxi or pushback, whichever comes first.

VFR Departure Clearance

For departing VFR flights, VFR departure clearance may be given together with the takeoff clearance. This includes:

  • The VFR route (for single-engine departures from BIKF/BIRK, if the aircraft is following one)
  • ...or the cardinal direction (N/E/S/W) if the aircraft is not on a VFR route.
  • (Optionally) The direction it should turn (left or right) after departure if it would be helpful to clarify for the pilot.

For aircraft departing BIKF/BIRK via a VFR route, since the route altitudes are published, it is not required to specify an altitude in the route clearance unless the pilot requests it. The following phraseology may be used:

[CALLSIGN], after departure [LEFT/RIGHT TURN] for route X, [WINDS], [RWY], cleared for takeoff.

For example:

🎧 (TF-)SKN, after departure left turn for route 6, winds 180 degrees 14 knots, runway 19, cleared for takeoff.

For aircraft departing not via a VFR route, an altitude should be specified in the departure clearance. The following phraseology may be used:

[CALLSIGN], after departure [LEFT/RIGHT TURN to]* leave the control zone to the [N/E/S/W], [ALT], [WINDS], [RWY], cleared for takeoff.

(*may be omitted)

For example:

🎧 (TF-)MYB, after departure right turn to leave the control zone to the East, 2500ft, winds 300 degrees 15 knots, runway 31, cleared for takeoff.

🎧 (TF-)ABB, after departure leave the control zone to the North, 1500ft, winds 300 degrees 15 knots, runway 31, cleared for takeoff.

Once the aircraft is airborne, the pilot should then be asked to report when they are approaching the boundaries of the CTR.

  • For BIKF & BIRK:
    • If on a VFR route, the pilot should report passing the reporting point immediately prior to the airspace boundary, e.g., Aluminium Factory for BIRK departures on route 6.
    • If not on a VFR route, the pilot should report 6 NM out from BIRK, or 12 NM out from BIKF.
  • Other aerodromes:
    • Aircraft may simply be asked to report 10 NM out from the airport, or “report leaving the control zone.”

Before an aircraft leaves the CTR, one must coordinate with any neighboring ATC whose airspace the aircraft will enter. One should inform the other controller of the aircraft’s callsign, altitude (current, as well as requested if different), and intentions.

Back to top